Cube Mould (Two Part) V Shape

Model No.: SET-1118 (A)

Standards:
 

Civil Lab Equipment Manufacturer Cube Mould Two Part V Shape is manufacturers as per the industry defined standards. Cube Mould (Two Part) V Shape are the commonly required in the laboratory.

manufacturing Cube Moulds as per international standards (BS and IS). SETEST cube moulds are available in different sizes with difference standards. For the metric size cube mould, the faces are machined flat to +/-0.2mm accuracy and finished to within 0.2mm. For the inch size moulds, the faces are machined flat to +/-0.01 inched to within 0.01in. All cube moulds are supplied complete with the base plate.

a. Cube Mould (Cast Iron – for Mortar) 50mm, Single Gang
b. Cube Mould (Cast Iron – for Mortar) 50mm, Three Gang
c. Cube Mould (Mild Steel – for Cement) 70.6mm, with Loose Base Plate
d. Cube Mould (Cast Iron – for Concrete) 75mm Single Gang
e. Cube Mould (Cast Iron – for Concrete) 100mm Light Weight
f. Cube Mould (Cast Iron – for Concrete) 100mm Clamp Type (8.5 KG) Four-Part
g. Cube Mould (Cast Iron – for Concrete) 150mm ISI Marked
h. Cube Mould (Cast Iron -for Concrete) 150mm Clamp Type (16 KG) Four-Part
i. Cube Mould (Cast Iron – for Concrete) 150mm Clamp Type (16 KG) Two-Part

Apart from Cast Iron and Mild Steel Cube Moulds, manufactures Plastic and Polyurethane Cube Moulds. manufactures Plastic and Polyurethane Cube Moulds.
More information on Plastic & Polyurethane cube moulds is available at: Plastic Cube Mould.

How to determine the compressive strength of concrete using Cube Moulds.
To determine the compressive strength of concrete, 6 concrete samples are prepared using cube mould. Freshly prepared concrete is poured into 6 cube moulds and is kept for curing for 7 & 28 days. The preferred size of concrete cube used in concrete testing is 150mm x 150mm x 150mm. On 7th day, 3 concrete samples are extracted from their respective cube moulds and compression test is performed using compression machine. A similar process is repeated on 28th day with remaing 3 concrete cubes.

When the force is applied on the concrete cube specimens, concrete starts to chip off and finally the specimen cracks. The force at which the specimen fails is noted and compressive strength of concrete cube is calculated. I.e, if the specimen cracks at 500kN force and size of specimen is 150 X 150 x 150 mm, the strength of cube will be (500 x 1000) / (150 x 150) N/sq. mm

Finally, the mean of all 6 concrete cube specimens, is used as the compressive strength of concrete.

Note:
Only IS, BS or ASTM cube moulds should be used to prepare concrete samples, so as to maintain accuracy of test results.

 
 
Concrete Testing Lab Equipment

Orimet Test Apapratus

Fill Box Apparatus

Vee Bee Consistometer Test

Concrete Slump Test Equipment

Ball Penetration Apparatus(Kelley Ball)

Compaction Factor Apparatus
Initial Surface Absorption Test Apparatus

Concrete Pocket Penetrometer

Spring Penetrometer

Bleeding Of Freshly Mixed Concrete

Tamping Rod

Tamping Bar

Straight Edge

Peak Load Indicators Manufacturer
Curing Tank

Concrete Vibrating Table

DLC Vibrating Hammer

Portable Handy Concrete Poker Vibrator

Lateral Extensometer
Longitudinal Compressometer

Sand Absorption Cone And Tamper

Density Of Fresh And Hardened Concrete

B Type Air Entrainment Meter

Air Entrainment Meter
Insulator Testing Machine

Fully Automatic Mortar Mixer Machine

Mortar Mixer Machine

Concrete Rebound Hammer Tester

Laboratory Mixer Pan Type With Extra Drum And Trolly ( Detachable Pan )